Browsing by Author "Ayinla, S.L."
Now showing 1 - 12 of 12
Results Per Page
Sort Options
Item Design and Implementation of an AC Power Generator using DC Motor(2020) Yusuf, O.A.; Kamil, K.R.; Ayinla, S.L.; Usman, U.A.; Gbigbadua, K.H.A reliable and efficient supply of electricity is an unavoidable prerequisite to the development of any nation since it is the major power source that drives most technologies. This paper describes the design and implementation of an AC power generator that generates electrical energy from an alternator using DC motor as the prime mover. The alternator armature shaft was coupled directly with the DC motor, which was powered by a high current rechargeable battery. The DC motor rotates the armature of the alternator in the field coil at high speed when powered. This results in two a.c output voltages of 12V and 220V from the alternator. The 12V output was feedback to recharge the battery by the means of a diode while the 220V output was used to drive any a.c load connected to the generator. The 12V output provides constant recharging of the battery as the DC motor consumes energy from the rechargeable battery. The system was also designed with control and display circuitries for automatic switching ON/OFF of the generator and to monitor the voltage output from the grid and generator to select the best output to the load respectively. It also incorporates a buzzer to give an alarm when a fault is detected and to isolate the load.Item Development of 3-Axes Accelerometer Wireless Sensor Nodes for Pipeline Monitoring(2019) Ayinla, S.L.; Ajiboye, A.T.; Yusuf, A.O.; Dilibe, C.G.; Ajayi, A.R.Item Effects of PID Controller on Performance of Dish Antenna Position Control for Distributed Mobile Telemedicine Nodes(Faculty of Engineering, University of Maiduguri, Nigeria, 2019) Ajiboye, A.T.; Ayinla, S.L.; Ajayi, A.R.Item Effects of PID Controller on Performance of Dish Antenna Position Control for Distributed Mobile Telemedicine Nodes(Faculty of Engineering, University of Maiduguri, Maiduguri, Nigeria., 2024-06) Ajiboye, A.T.; Ajayi, A.R.; Ayinla, S.L.Item Effects of PID Controller Position in Control System Loop on Time Domain Performance Parameters(2018) Ajiboye, A.T.; Ayinla, S.L.; Yusuf, A.O.Item Effects of PID Controller Position in Control System Loop on Time Domain Performance Parameters(Computer Chapter of the Nigeria Section of the Institute of Electrical and Electronics Engineers (IEEE) Inc, New York, USA, 2018) Ajiboye, A.T.; Ayinla, S.L.; Yusuf, A.O.Item Optimal control of DC motor using leader-based Harris Hawks optimization algorithm(2024) Ayinla, S.L.; Amosa, T.I.; Oladimeji, I.; Rahman, M.; Bahashwan, A.A.; Mostafa, M.G.; Yusuf, A.O.Item PID controller for microsatellite yaw-axis attitude control system using ITAE method(Universitas Ahmad Dahlan (UAD), 2020) Ajiboye, A.T.; Popoola, J.O.; Oniyide, O.; Ayinla, S.L.Item Undergraduate computer engineering laboratory manual (Vol. 2): measurement & instrumentation; digital electronic circuits; data communication & networks.(Published by Department of Computer Engineering, University of Ilorin, Ilorin, Nigeria, 2017) Opadiji, J.F.; Ajiboye, A.T; Olatunji, S.A.; Ayinla, S.L.; Ajayi, A.R.; Yusuf, O.A.; Labiran, O.O.; Mahmud, H.O.; Adebayo, O.F.Item Undergraduate computer engineering laboratory manual (Vol. 2): signal measurement & instrumentation; digital electronic circuits; data communication & networks(Department of Computer Engineering, University of Ilorin, Ilorin, Nigeria, 2017) Opadiji, J.F.; Ajiboye, A.T.; Olatunji, S.A; Ayinla, S.L.; Ajayi, A.R.; Yusuf, O.A.; Labiran, O.O.; Mahmud, H.O.; Adebayo, O.F.Item Undergraduate computer engineering laboratory manual (Vol. 3): microprocessor system interfacing; prototyping and packaging; artificial intelligence applications(Department of Computer Engineering, University of Ilorin, Ilorin, Nigeria, 2018) Opadiji, J.F.; Ajiboye, A.T.; Olatunji, S.A.; Ayinla, S.L.; Ajayi, A.R.; Yusuf, O.A.; Mahmud, H.O.; Adebayo, O.F.Item Undergraduate computer engineering laboratory manual (Vol. 3): microprocessor system interfacing; prototyping and packaging; artificial intelligence applications.(Published by Department of Computer Engineering, University of Ilorin, Ilorin, Nigeria., 2018) Opadiji, J.F.; Ajiboye, A.T.; Olatunji, S.A.; Ayinla, S.L.; Ajayi, A.R.; Yusuf, O.A.; Mahmud, H.O.; Adebayo, O.F.